Kirkwood HVAC & Plumbing Services

Installed customer-provided flush-mount ceiling light fixture in bedroom, including electrical connections, secure mounting to ceiling junction box, and verification of proper operation. Additional work was completed as requested on-site.

Completed cooling system tune-up on 10-year-old outdoor AC unit that was originally scheduled due to no cooling condition. Performed standard maintenance procedures including system diagnostics with digital manifold gauges to verify refrigerant pressures and temperatures, and inspected/documented dirty 16x25x1 air filter requiring replacement. All measurements recorded and system operational upon completion.

Responded to service call for thermostat replacement on single ground-level HVAC unit located in rear of property. Removed existing thermostat and assessed electrical connections and wall mounting conditions. Completed installation of new digital thermostat, secured all wiring connections, and verified proper operation with system controls.

Responded to no cooling call on 10+ year old outdoor unit with non-operational condenser fan. Upon arrival, performed diagnostic evaluation of the system and documented equipment condition. Unable to determine specific repairs completed from available documentation, but unit was assessed and customer was provided with findings and repair recommendations.

Responded to a no-power condition affecting Ring doorbell system. Investigated electrical panel and traced affected circuit through attic space. Inspected wire connections at junction points, identifying loose or compromised connections in the attic area. Secured and properly terminated all affected wiring with appropriate wire nuts. Verified circuit integrity at main panel, confirmed proper breaker operation, and restored power to doorbell circuit. System tested and functioning normally upon completion.

Responded to no cooling complaint on 10+ year old portable air conditioning unit located in sunroom. Upon arrival, confirmed unit was operating but providing inadequate temperature differential of only one degree from outdoor ambient temperature. Performed diagnostic evaluation and documented unit condition with photographs for customer records.

Installed a 40-gallon gas tall water heater from existing inventory in accordance with City of Kirkwood permit #PLUM-26-0443. Removed old unit, connected gas supply line and water piping, installed new brass fittings, and verified proper venting through existing ductwork. System tested and operational upon completion.

Responded to no cooling complaint on ground-level condenser unit. Upon inspection, identified failed dual-run capacitor preventing compressor operation. Replaced defective capacitor with new unit and restored system to normal operation. Advised to shut AC off temporarily and run fan only until repair was completed to prevent further strain on system components.

Responded to no-cooling call on unit U10 located at side of home. Customer reported thermostat disconnect the previous day with unit failing to operate even after thermostat was reconnected. Upon arrival, performed diagnostic inspection of control board and wiring connections. Inspected circuit board components, wiring harnesses, and multi-pin connectors for signs of failure or loose connections. Verified proper wire terminations at control board terminals and checked for damaged components. Photographed internal control board assembly and wiring configuration for documentation purposes. System evaluated and necessary repairs completed to restore proper operation.

Completed drain line repairs in attic space for HVAC system experiencing no cooling issue. Installed approximately 8 feet of 3/4-inch PVC pipe with 45-degree elbow fitting and 10-12 feet of 5/8-inch vinyl tubing to restore proper condensate drainage. Used nitrogen to clear blockages and verify proper flow through repaired drain line system.

Responded to no-cooling complaint on 10+ year old outdoor unit located at side of home. Upon arrival, system was operational but performed full diagnostic evaluation using digital manifold gauges and amp clamp to assess system performance and refrigerant charge. Measured electrical parameters, operating pressures, and temperatures at outdoor condenser unit. Inspected indoor air handler in attic space, checking refrigerant lines, condensate drain system, and electrical connections. System currently functioning but requires monitoring for intermittent operation issues reported by customer.

Completed comprehensive cooling maintenance on two 9-year-old AC systems per customer request for early morning service. Performed standard tune-up procedures on both units including inspection of evaporator coils, condenser coils, refrigerant levels, electrical connections, and airflow components. Both systems tested and confirmed operational with no deficiencies noted; all equipment functioning within manufacturer specifications.

Responded to no cooling call with reported water leak from third-floor AC unit into bathroom below. Upon arrival, located 10+ year old air handler in crawlspace and identified condensate drain line obstruction causing overflow and water damage to ceiling. Cleared blockage from drain line, tested drainage flow, and verified unit operating properly with no further leakage.

# HVAC No Cool Service Call Responded to service call for air conditioning unit not cooling with reported fan issue. Upon arrival, found unit shut off in backyard location. Performed diagnostic inspection of single AC system of unknown age. Accessed air handler and evaporator coil assembly for thorough examination. Observed copper evaporator coil with multiple parallel tube rows in proper configuration. Inspected condensate drain pan and float switch assembly for proper operation. Noted significant accumulation of dust, debris, and deteriorated insulation material throughout air handler cabinet and on internal components including mounting brackets, copper tubing, and heat exchanger coil fins. This heavy contamination indicated extended period without maintenance and potential airflow restriction issues. Examined blower assembly, capacitor, and electrical connections. Multiple wire connections inspected including control wiring. Evaluated finned coil section and mechanical mounting

Responded to no-cool call on a 2-year-old system with 2 AC units serving 3 zones. Upon arrival, diagnosed power issue preventing blower fan operation. Installed new White-Rodgers non-programmable digital thermostat and replaced second thermostat per customer request for programmable unit on main floor. Verified all electrical connections at air handler, inspected control board and capacitor wiring. Restored power to system, tested all zones for proper operation, and confirmed cooling cycle engagement across all units.

Installed a 50-gallon tall gas water heater in basement utility area, completing all copper piping connections to existing overhead plumbing system. Coordinated afternoon arrival for equipment pickup and verified City of Kirkwood permit requirements, which did not require plumbing ID sticker for this installation. All connections tested and system operational upon completion.

Completed electrical repairs addressing multiple fixture and switch issues throughout the property. Replaced non-functioning pull chain switch on garage loft light fixture, installed new light bulbs in basement fixtures, diagnosed and replaced faulty bathroom fan switch while verifying light switch operation remained intact, and replaced defective switch in garage to restore proper functionality. All fixtures tested and confirmed operational upon completion.

Completed installation of 50-gallon tall electric water heater in basement utility area. Unit was set up and prepared for delivery with all necessary plumbing connections, including copper piping, expansion tank, and flexible connectors properly installed per manufacturer specifications and local code requirements.

Performed comprehensive cooling system tune-up on a single unit located in side yard. Upon inspection, discovered significant debris accumulation on evaporator coil and blower wheel assembly, restricting airflow and reducing system efficiency. Cleaned blower wheel to remove dust buildup and thoroughly cleaned evaporator coil to eliminate dense fiber and lint accumulation that had collected on coil surfaces. Documented pre-service conditions with photographs showing extent of contamination on both components. Restored proper airflow through system, improving cooling performance and operational efficiency.

Completed comprehensive cooling system tune-up on 2-year-old Lennox unit per manufacturer specifications. Performed visual inspection of condenser coil assembly, confirming clean fins with no debris accumulation or corrosion present. Inspected control board and electrical connections, verifying all wiring terminals secure and circuit board components functioning properly. Unit operating within normal parameters with no issues identified during service.