Kirkwood HVAC & Plumbing Services

Responded to service call for non-functioning light fixture and intermittent ceiling fan light issue in bedroom. Troubleshot pindon light that remained inoperative after bulb replacement, identified electrical fault, and restored functionality. Diagnosed and repaired ceiling fan causing intermittent light operation in bedroom, ensuring reliable operation of both lighting circuits.

Responded to a basement drain backup with sewage overflow. Upon arrival, located the main sewer cleanout access point in the backyard and removed the cap to assess the blockage. Utilized a power auger with flexible cable to clear the obstruction in the main sewer line. Successfully restored proper drainage flow and verified system functionality. Replaced cleanout cap and secured all access points upon completion.

Responded to a no-power condition affecting backyard light fixtures. Upon inspection, accessed the main electrical panel and identified a tripped circuit breaker serving the exterior lighting circuit. Reset the breaker and verified power restoration to all affected fixtures in the backyard area.

Replaced defective thermal expansion valve (TXV) on system S/N 1522G74733 to restore cooling operation. Unit was experiencing no-cool condition due to failed TXV. Recovered refrigerant, removed old valve assembly, installed new TXV with proper torque specifications on brass fittings, evacuated system, and recharged to manufacturer specifications. Verified proper system operation with temperature differential and pressures within normal range. Retained failed part per protocol.

Responded to service call for 18-year-old Comfortmaker air conditioning system experiencing intermittent operation and shutting off on its own, affecting entire home cooling. Performed comprehensive U10 cooling maintenance service as part of annual preventative maintenance program. Conducted thorough inspection of outdoor condensing unit, verifying proper airflow through condenser coil fins and checking overall component condition. Inspected and assessed indoor blower wheel assembly, noting dust accumulation on blower housing and wheel blades. Cleaned blower components to restore optimal airflow and system efficiency. Verified proper system operation following maintenance procedures. Unit returned to normal operation with improved performance after cleaning and inspection protocol completed.

Responded to no cooling complaint on three-year-old Lennox system affecting entire residence currently under construction. Upon arrival, performed diagnostic testing of unit and measured supply air temperature at 59°F, indicating inadequate cooling performance. Inspected indoor air handler, ductwork, and refrigerant lines in mechanical space to identify root cause of cooling failure and restore proper system operation.

Responded to no cooling complaint on 9-year-old Trane (Ameristar) system with thermostat set at 79°F but house temperature remaining at 83°F. Upon inspection, discovered severely damaged low-voltage wiring outside the unit with deteriorated insulation and exposed copper conductors. Replaced damaged wiring, restored proper electrical connections, tested system operation, and verified cooling cycle restored to normal functionality.

Responded to no-cooling call on residential air conditioning system over 10 years old. Upon arrival, found condenser fan motor inoperative with visible signs of wear, dirt accumulation, and environmental exposure on motor housing and mounting components. Diagnosed failed condenser fan motor preventing proper heat rejection from outdoor unit, confirmed unit was safely turned off per prior instructions to prevent compressor damage from inadequate airflow.

Completed preventive maintenance tune-up on two cooling systems. Performed comprehensive inspections including electrical measurements with digital clamp meter to verify proper amperage draw and system performance. Inspected air filtration components, noting accumulated dust and debris on mesh filter requiring attention. Both systems operational and running within normal parameters upon completion of maintenance procedures.

Responded to no cooling call with reported intermittent fan operation and unusual noise. Upon inspection, found severely restricted airflow due to heavily clogged air filter with significant dust and debris accumulation. Replaced dirty filter and verified proper system operation. Unit tested successfully with normal cooling cycle, consistent fan operation, and no abnormal sounds. System restored to proper working condition.

Responded to callback for less than one-year-old Lennox unit running continuously without adequate cooling. Upon inspection, diagnosed and replaced failed dual-run capacitor, which was preventing compressor from operating at full capacity. System tested after replacement, confirmed proper cooling operation and normal runtime cycles restored.

Responded to no cooling complaint on 23-year-old residential air conditioning system. Upon arrival, observed outdoor condenser unit experiencing fan motor failure - compressor would start but condenser fan would slow down and stop, preventing proper heat rejection and system cooling. Diagnosed failed condenser fan motor on aging outdoor unit. Performed necessary repairs to restore cooling operation to the residence.

Responded to water leak complaint in basement around HVAC equipment. Upon inspection, discovered clogged condensate drain line causing water overflow and accumulation on floor. Cleared blockage from drain line, removing accumulated debris and sediment that had restricted proper drainage. Verified condensate system flowing freely and tested equipment operation to ensure proper function. Cleaned up water and debris from floor area surrounding unit.

Completed comprehensive air conditioning tune-up service on single outdoor condensing unit for Home Depot work order #F59536971. Performed standard preventive maintenance inspection including checking refrigerant levels, cleaning condenser coils, testing electrical connections, verifying proper airflow through grilles, and inspecting the condenser fan operation. Verified and replaced 14x20x1 pleated air filter at the indoor air handler unit, ensuring optimal system performance and air quality for the residential HVAC system.

Responded to callback for HVAC system continuing to leak after previous repair. Accessed unit in attic and inspected condensate drain system and evaporator coil assembly. Upon examination, identified improper drainage from primary drain line and inspected drain pan for cracks or overflow conditions. Evaluated PVC drain piping configuration and brass fittings for proper connections and flow. Checked insulated refrigerant lines and surrounding areas for moisture accumulation. Documented current condition of drain pan, piping connections, and ductwork installation with photos showing metal drain pan assembly, PVC drain components, and flexible ductwork in attic space. Further diagnostic work required to identify source of persistent leak and implement permanent solution.

Responded to callback for attic-mounted HVAC unit with clogged condensate drain line. Cleared blockage from drain pipe to restore proper water drainage from system. Verified condensate pump operation and confirmed all electrical connections secure. System tested and operating normally with proper drainage flow restored.

Responded to no cooling call and inspected Rheem HVAC system with digital control panel. Found multiple system alarms in history including low refrigerant pressure, line voltage brown out, water sensed, and no blower communication errors. Documented alarm history via thermostat display for diagnostic purposes and further troubleshooting of intermittent system failures.

Responded to no cooling complaint on 3-year-old Daikin system with Daikin One Plus smart thermostat. Upon arrival, found thermostat display showing 82°F room temperature but system not actively cooling. Verified thermostat power supply, checked communication between thermostat and outdoor unit, and confirmed proper system settings and scheduling functions. Cycled system through cooling mode, verified compressor engagement, and confirmed normal operation restored. Instructed customer on proper thermostat operation and schedule settings to prevent future issues.

Conducted on-site evaluation of existing outdoor electrical service equipment for meter box replacement estimate. The current installation includes a weathered green metal panel with exposed internal wiring and circuit breakers, an aged utility meter displaying significant rust and corrosion on the housing, and auxiliary weatherproof junction boxes mounted to the brick exterior. Documented the deteriorated condition of the service equipment, noting rust staining around mounting points, accumulated debris in the panel, and water damage indicators on surrounding surfaces. Photographed the complete electrical service configuration including conduit routing, panel positioning relative to other utility equipment, and the overall site layout to provide accurate material and labor estimates for new meter box installation.

Performed comprehensive preventive maintenance on roof-mounted cooling unit less than 10 years old. Conducted complete system inspection including blower assembly operation verification, electrical component testing with digital multimeter showing 323-ohm reading, and airflow assessment. Cleaned blower wheel, checked motor operation, inspected wiring connections and capacitor, and verified all mechanical components functioning within normal parameters.